
The Invacare Tube Style Armrest Bracket fits Invacare Powerchairs that utilize a round tube to support the underside of the armrest. There is a screw approximately 2" from the end of the tube that goes through the tube and secures the armrest in place. This screw is required to mount the bracket. Please confirm the location of the screw before ordering the bracket.
If you have any questions about the suitability of this bracket for your chair please contact SnapIt! by phone or email at 903-965-9181 or customerservice@snapitproducts.com.
The Merits Powerchair Bracket attaches to the underside of the armrest utilizing the existing screw located about 3 1/2" from the end of the armrest. Remove the existing screw using an allen wrench, insert the screw through the bracket on the counterbore side back into the armrest and retighten.
Once installed snap the SnapIt! accessory into the bracket.
For additional detail see the Installation Instructions below.
The Dalton Powerchair Bracket attaches to the underside of the armrest utilizing the existing screw located about 3 1/2" from the end of the armrest. Remove the existing screw using an allen wrench, insert the screw through the bracket on the counterbore side back into the armrest and retighten.
Once installed snap the SnapIt! accessory into the bracket.
For additional detail see the Installation Instructions below.
The Hoveround Powerchair Bracket attaches to the underside of the armrest utilizing the existing screw located approximately 3 1/2" from the end of the armrest. Remove the existing screw using an allen wrench, insert the screw through the bracket on the counterbore side back into the armrest and retighten.
Once installed snap the SnapIt! accessory into the bracket.
For additional detail see the Installation Instructions below.
The Golden Powerchair Bracket mounts under the armrest of some Golden Powerchairs. The bracket slides into the square receptacle under the armrest which is found on some Golden Powerchairs. The bracket is secured in place by tightening the set screw on the bottom of the square receptacle. Not all Golden Powerchairs have this feature. Please see the Golden Compass Sport and the Golden LiteRider Envy for alternate Golden brackets. Also, some of the Golden Alante Sport have the receptacle on the joystick control side but not on the other armrest. In this
The Shoprider Powerchair Bracket mounts to two 6mm tapped holes on the underside of the armrest utilzing two 6mm screws supplied with the bracket.
Raise the armrest and locate the two 6mm tapped holes in a rectangular pocket. (If your armrest does not have the two tapped holes contact SnapIt! by phone or email at 903-965-9181 or customerservice@snapitproducts.com.) Attach the bracket to the armrest using the two supplied screws with a philips screwdriver.
Once the bracket is installed snap the SnapIt! accessory into the bracket.
The Golden LiteRider Envy Powerchair Bracket mounts to two 6mm tapped holes on the underside of the armrest utilzing two 6mm screws supplied with the bracket.
Raise the armrest and locate the two 6mm tapped holes in a rectangular pocket. (If your armrest does not have the two tapped holes contact SnapIt! by phone or email at 903-965-9181 or customerservice@snapitproducts.com.) Attach the bracket to the armrest using the two supplied screws with a philips screwdriver.
Once the bracket is installed snap the SnapIt! accessory into the bracket.
The Golden Compass Sport Powerchair Bracket mounts to two 6mm tapped holes on the underside of the armrest utilzing two 6mm screws supplied with the bracket.
Raise the armrest and locate the two 6mm tapped holes in a rectangular pocket. (If your armrest does not have the two tapped holes contact SnapIt! by phone or email at 903-965-9181 or customerservice@snapitproducts.com.) Attach the bracket to the armrest using the two supplied screws with a philips screwdriver.
Once the bracket is installed snap the SnapIt! accessory into the bracket.
The Permobile Powerchair Bracket mounts in the Dual "T" Track aluminum extrusion underneath the armrest utilizing screws and nuts supplied with the bracket.
Open access to the end of the Dual "T" Track extrusion is required for mounting the bracket. Click on the photo and select next to see a photo of the Dual "T" Track.
Loosen the screws and nuts supplied with the bracket enough to be able to slide the nuts into the two "T" Tracks and retighten.
Once installed snap the SnapIt! accessory into the bracket.